SV08/ voron for the folks that like to tinker (and value not living in a walled garden, Sovol’s hot end/ nozzles not withstanding).

I would call the SV08 hot end/nozzles proprietary-ish. They still published everything on github, which enabled the community to design a modified heat sink (that I got printed on PCBWay). The updated heat sink allows you to swap in an E3D Revo nozzle. That wouldn’t be possible if it was truly proprietary.

I’m surprised you saw that much of a speed improvement, but I guess I ran my old i3 clone somewhat fast.

My tuned/reliable profile (on Prusaslicer) on the Ender 3v2 was 40-60 mm/s and acceleration 200 mm/s^2. The stock profile (on Orca) for the SV08 is 200-300 mm/s and acceleration of 20000 mm/s^2. That’s probably why such a dramatic speed increase.

Were you homing z with the bed cold? If homing z involves touching the build plate, I could see this.

The auto z-offset on the SV08 heats the bed to 65, then does a QGL, followed by cleaning the nozzle, then the z-offset calibration (using the inductive probe on both the bed and the z-offset probe), followed by a bed mesh, then a test print. Most of what I’ve read is that the heater is not the most efficient at heating the bed up completely. That’s why everyone (Sovol included) recommend heat soaking for the initial z-offset. After I did that, I’ve had no problems with first layers.

I have an Ender 3V2 that I converted to direct drive with linear rails and CR Touch, and was pretty happy with the reliability of it. I’ve been wanting to build a Voron forever, but the amount of hours to build/cost of a kit (I can’t print ABS) was a barrier to entry.

I just picked up a Sovol SV08, which is a derivative of the Voron 2.4 (there are some proprietary parts on it, but $579 vs. $1000-1200 for a kit, I’m OK with that). I’m pretty happy with it thus far, although it did require some initial tinkering. Here are the highlights:

• Core XY
• Enclosure Ready
• Fast (printed something that took 26 hours on the Ender, and it took less than 4 on the SV08).
• Finicky for the initial z-offset. Heat soak the bed for 30 min at 65 degrees, then run the automatic z-offset.
• Got super frustrated why I couldn’t figure out the inconsistent extrusion/shitty prints. Tightened the tension screw on the extruder. Problem solved (rookie move).

Time will tell if it’s a long term printer, or more of a tinkerer. However, they open sourced it all - and there’s already a ton of mods. Printing the housing for the BTT 5" touchscreen, saving me $50 over buying a touchscreen from Sovol. It might be worth a look.

OpenMediaVault (OMV) is a Debian server with a very user-friendly web interface. It also has solid documentation and a robust community. I’ve been running it for 6 years, and I am very happy with it.

The problem isn’t with Nextcloud (I had the same issue happen with me). The problem is with the default sync settings on Thunderbird and DAVx5 (at least for me). Thunderbird defaulted to a longer than I wanted synch schedule, so I dropped it down to syncing every 15 minutes. DAVx5 was set to 240 minutes unless the event was created on my phone. Once I updated both schedules to every 15 minutes, I haven’t noticed an issue.

OpenMediaVault is a Debian server with a Web UI.

AM5 sockets are now LGA like Intel. AM4 was the last PGA socket, so bent pins on the chip are a thing of the past. Make sure to leave the socket cover in place while installing the CPU. Now, the fear is bending a pin on the MoBo.

For Corsair - I’ve been very happy with ckb-next. https://github.com/ckb-next/ckb-next

It is pretty robust, allows remapping of key/button bindings, changing of RGB, DPI, etc. Their goal is to replace iCUE. Very robust for mice and keyboards, but they also list other hardware that it is known to work with in their wiki. Might be worth a look.

I might have to downvote you. After all that, you could probably afford one. Forget a RAID though.

I use Cryptomator. Does exactly what you describe.

I’ve been pretty happy with the consistency of both Inland and Overture.