Watching TC do a video about something I do professionally has been a bit of a trip. For context, I work with freeze dryers (we call them lyophilizers) in pharmaceuticals rather than foods. I help design the lyophilization cycles for biologics and gene therapy products that get preserved through freeze drying. Until this video, I had no idea that people used these instruments for at-home food preservation (which is kind of insane imo).
The instruments that I work with are typically a much larger version of the bench-scale machine that he is using (usually one of the LyoStar line). However, I have used smaller, bench-scale units as well for some quick and dirty work. I included some pictures at the end behind a spoiler tag. Happy to answer any questions people have.
Some differences in how I use lyophilizers in a scientific setting as opposed to a home-use food setting:
Typically, we only lyo products that are already filled in vials as opposed to a full tray like he’s done.
We don’t pre-freeze our products before they go into the lyophilizer. Instead we refrigerate the shelf that the vials are sitting on to freeze the contents before we proceed to the drying steps.
Speaking of the shelves, in our instrument, the shelves can move up and down. This is used to compress the vials after the cycle is completely done, fully seating the vial stoppers and sealing them before we open up the main door.
Also speaking about stoppering the vials, we typically allow some nitrogen into the chamber before sealing up the vials, at a pressure moderately less than atmospheric pressure. This helps keep the vial sealed until it is properly crimped with a seal.
When it comes to drying, we do it in two stages. The primary drying step is when our product is kept cold, but put under vacuum. This removes most of the water, but not enough for our purposes. The secondary drying step is when the product is heated while the vacuum is maintained. This removes the rest of the water. We typically shoot for a residual moisture of <1% for a good cycle.
He talks about how long the process takes. I have worked on processes that take from 1-5 days. Typically, the lyophilizer is limited with how much liquid can be removed per unit time. This limit is determined by the geometry of the vent that connects the main chamber with your vials, and the chamber containing the condenser. Also, if you try to dry too quickly, it can damage the product you are trying to preserve.
He has some discussion at the end about the end of the cycle and the progress bar. What the instrument is doing is comparing the vapor pressure in the chamber using two different sensors. One of those is sensitive to the vapor pressure of water vapor, and the other is not. So, when things are fully dried out, those two are going to read the same pressure. While drying is still occurring, the sensor that detects water vapor will read a higher pressure. So, the instrument will continue to extend drying until those two pressures are the same.
Some Pictures
Benchtop lyophilizer that I have experience using. You can see some vials lined up inside the door. I have never used the bottle connections hanging off the side:
One of the trays of vials that is loaded before going into the lyophilizer. The vials that are partially stoppered in the middle of the tray actually contain the drug. All the vials without stoppers are empty and simply there to help hold things in place as well as distribute heat predictably through the tray. The stoppered vials in the corners are there to help distribute the weight as the shelves compress to fully seat the stoppers.
Here are a small number of vials that I ran on a benchtop unit without any spacer vials or the tray. I would never do this for any reason other than to take a picture like this. This is a good view of what a partially stoppered vial looks like. It allows a path for water vapor to escape out the top of the vial.
Finally, here is a vial post-lyophilization. The liquid has turned into a solid, white cake at the bottom of the vial. This is because most lyophilization formulations include sugars that provide structure for the cake and keep it porous. The sugars provide protection against freeze/thaw stress for the molecule of interest as well. The porosity of the cake allows for quick and easy reconstitution by adding water, usually in <30 seconds or so.
The products I work on are mostly monoclonal antibodies (and the occasional gene therapy product mixed in). So, the types of diseases they are used to treat vary. To be honest, I work on the process/formulation side of the development pipleline and the actual clinical treatment part is pretty much inconsequential to what I do. Some of the past programs I have worked on include treatments for asthma, eczema, multiple myeloma, breast cancer, MS, hemophilia, and tons of others that I don’t remember. Often, when dealing with antibodies, the same medicine can be effective for multiple indications.
The finished vials, post-lyophilization, sealing, labeling, and packaging, are sent to infusion clinics. There, clinicians will add water to the vials to reconstitute the drugs and then administer them to patients via IV (usually).
Watching TC do a video about something I do professionally has been a bit of a trip. For context, I work with freeze dryers (we call them lyophilizers) in pharmaceuticals rather than foods. I help design the lyophilization cycles for biologics and gene therapy products that get preserved through freeze drying. Until this video, I had no idea that people used these instruments for at-home food preservation (which is kind of insane imo).
The instruments that I work with are typically a much larger version of the bench-scale machine that he is using (usually one of the LyoStar line). However, I have used smaller, bench-scale units as well for some quick and dirty work. I included some pictures at the end behind a spoiler tag. Happy to answer any questions people have.
Some differences in how I use lyophilizers in a scientific setting as opposed to a home-use food setting:
Some Pictures
Benchtop lyophilizer that I have experience using. You can see some vials lined up inside the door. I have never used the bottle connections hanging off the side:
One of the trays of vials that is loaded before going into the lyophilizer. The vials that are partially stoppered in the middle of the tray actually contain the drug. All the vials without stoppers are empty and simply there to help hold things in place as well as distribute heat predictably through the tray. The stoppered vials in the corners are there to help distribute the weight as the shelves compress to fully seat the stoppers.
Here are a small number of vials that I ran on a benchtop unit without any spacer vials or the tray. I would never do this for any reason other than to take a picture like this. This is a good view of what a partially stoppered vial looks like. It allows a path for water vapor to escape out the top of the vial.
Finally, here is a vial post-lyophilization. The liquid has turned into a solid, white cake at the bottom of the vial. This is because most lyophilization formulations include sugars that provide structure for the cake and keep it porous. The sugars provide protection against freeze/thaw stress for the molecule of interest as well. The porosity of the cake allows for quick and easy reconstitution by adding water, usually in <30 seconds or so.
What an interesting read. You made my day!
What are thaw things you process used for?
The products I work on are mostly monoclonal antibodies (and the occasional gene therapy product mixed in). So, the types of diseases they are used to treat vary. To be honest, I work on the process/formulation side of the development pipleline and the actual clinical treatment part is pretty much inconsequential to what I do. Some of the past programs I have worked on include treatments for asthma, eczema, multiple myeloma, breast cancer, MS, hemophilia, and tons of others that I don’t remember. Often, when dealing with antibodies, the same medicine can be effective for multiple indications.
The finished vials, post-lyophilization, sealing, labeling, and packaging, are sent to infusion clinics. There, clinicians will add water to the vials to reconstitute the drugs and then administer them to patients via IV (usually).
I’ve reconstituted a ton of lyophilized vials of controls for medical lab analyzers. Interesting to hear about how they’re made, thanks for sharing.